QEA. ACTIVE. CDIP. J. 1. TBD. A N / A for Pkg Type. to QE. A. SNJAJ. QFA. ACTIVE. CFP. W. BCD to 7-Segment Decoder. General Description. The ‘LS48 translates four lines of BCD () input data into the 7-segment numeral code and provides seven. DATASHEET, This package accepts a positive-logic Binary Coded Decimal (BCD) input and converts it to the proper pattern necessary to.

Author: Balkis Goltirg
Country: Netherlands
Language: English (Spanish)
Genre: Love
Published (Last): 11 May 2016
Pages: 319
PDF File Size: 10.81 Mb
ePub File Size: 2.18 Mb
ISBN: 366-8-35773-517-8
Downloads: 55955
Price: Free* [*Free Regsitration Required]
Uploader: Nadal

7448 BCD to 7-Segment Decoder

Yes, my password is: You May Also Like: A microcontroller can be programmed to perform the binary to decimal conversion and then use a look-up chart to perform the segment conversion. This package accepts a positive-logic Binary Coded Decimal BCD input and converts it to the proper pattern necessary to illuminate a 7 segment display. A discussion of Musk’s past success and future plans. To build a simple digital counter, consider using devoder decade counter.

Oct 5, 3.

Can thermal cameras can be a beneficial tool for electrical engineers? Thermal Cameras for Electrical Engineers? D is the MSB of the digit. Wire the with the display as you would if you wanted to display all the numbers. A PWM pulse-width modulated signal can be applied to this pin to provided varying brightnesses to the LED display being driven, allowing user control of LED dimming for applications such as power saving by decreasing the brightness during times of low ambient light.


Discussion in ‘ The Projects Forum ‘ started by cjjgOct 5, No, create an account now. A high output is intended to light the segment.

Oct 6, 4. Feb 4, 4, Embedded Systems and Microcontrollers.

Shown above, is an example application of the 74LS48 7-seg decoder circuit. The potential for medical applications could be huge. Oct 5, 2. Read the datasheet for the pin configuration.


In this method, the microcontroller would send BCD binary coded decimal on 4 output pins to the chips. Oct 5, 1.

Oct 5, 2 0. The decimal point indicator on this volt-meter as well as the colons “: Quote of the day. The Decooder gates will take signal from the output of the counter or whatever drives the four inputs of the Finally, use combinations with AND gates to control the LT pin lamp test and zero blanking control RBI to turn on all the leds or turn them all off at the desired numbers.

Other than a little more conditional logic connections and a few more stages, there’s nothing stopping you from building a 4748 digital clock with hours, minutes, and seconds. The outputs are open-collector but have internal 2K ohm pull-up resistors and have a maximum low-level output sink current defoder 6 milliamperes 6mA. Jul 17, 22, 1, Common cathodemeaning the negative connection of all of the LEDs is tied together.


BCD TO 7-SEGMENT DECODER – Mikroelectron – Mikroelectron

All segments are cecoder when a low logical zero signal is applied to pin 4 OUT. Your name or email address: A line selector an additional output line on the microcontroller could select which chip to target and cycle through the decoded of displays to produce the overall numeric output. However, if pins are limited on the microcontroller, it can be advantageous to use ICs in a multiplexing fashion to drive the 7-segment displays.

Pin – Function 1 – B input 2 – C input 3 – Lamp test input, hold low for normal operation 4 – RB output should normally read the same as RB input 5 – RB input This must be open no connection or held high 6 – D input 7 – A input 8 – Gnd 9 – e segment 10 – d segment 11 – c segment 12 – b segment 13 – a segment 14 – g segment 15 – f segment 16 – Vcc.

Decover you already have an account?